I can't move my fence 10 inches off the wall, and so my only option now (I think) is to somehow attach the 4x4 PT fence post to the side of the retaining wall. I'm installing a 6 foot tall panel fence, with posts every 72".
To attach a wood handrail post to concrete: Mark the location of the holes in a metal post bracket on the concrete. Drill holes in the concrete of the right diameter for lead shields using a …
You would really need to notch the posts (so that the post's length continues down vertically) and lag them onto the sides of the concrete or the block wall using galanized concrete sleeve anchors and galvanized lags or bolts.
Since this post size is smaller than a conventional 4x4 wooden post, it is easier to drill and can cause less stress on the concrete pad. Depending on the strength of your concrete, you can either drill all the way through like in Solution # 2, or set the chain link fence posts with hydraulic cement.
Attaching wooden posts to a poured concrete slab. Attaching wooden posts to a poured concrete slab (post #201241) BigMish on Tue, 04/19/2011 - 05:52 . in . General Discussion; I have an old concrete slab in my backyard from an outbuilding that I tore down. I’d like to put a pergola on this slab.
Find out how to attach a wood handrail post securely to concrete using lead shields and a metal post ... Attaching stringers to posts when building a wooden fence. ... Gray and white decorative vertical stripes painted on walls.
In this project, we show you how to anchor post to concrete. In our case, we had to build stair railings and consequently we needed to attach post to concrete.
Re: Attaching A Post To Foundation Wall.. That concrete that is sticking out helps to deflect snow and water away from the footing. Breaking off the projecting concrete or drilling in to the footing is just a recipe for problems.
A third option for attaching a post to solid concrete or concrete block is side mounting, which works well on an elevated masonry base, such as steps or a raised concrete porch. A good rule of thumb when side mounting is to attach at least one-third of the post below the top level of the concrete.
I can't move my fence 10 inches off the wall, and so my only option now (I think) is to somehow attach the 4x4 PT fence post to the side of the retaining wall. I'm installing a 6 foot tall panel fence, with posts every 72". ... and then to bolt the post to the concrete wall using some type of a wedge anchor and epoxy. What do you all think ...
Attaching wooden posts to a poured concrete slab. Attaching wooden posts to a poured concrete slab (post #201241) BigMish on Tue, 04/19/2011 - 05:52 . in . General Discussion; ... What would be the best way to attach the posts to the slab?
Concrete, concrete block, mortar, brick, tile and stone. How to use: Drill a pilot hole at the proper location with a hammer drill and masonry bit to the depth your screw will penetrate. Tap the plastic anchor into the hole. It should fit snugly but drive in easily with a hammer.
Attaching a post to a concrete block wall in .....>> Attach Wood To Concrete Video | Ask the Builder . AsktheBuilder: Tim Carter demonstrates a really simple way to nail wood to a concrete floor or wall. ... Attach Wood To Concrete Video DIY | DIY Videos .....>> how to attach concrete wall to wood post - WPC Deck Suppliers . Feb 9, 2013 .
Reader Approved How to Add Concrete to Existing Concrete. Four Parts: Cleaning Old Concrete Setting up a Slab Perimeter Pouring a Primer Coat Adding the Top Layer Community Q&A No matter how strong a slab of concrete seems, it will wear out over time. Imperfections form when concrete hardens or sinks into the ground.
Re: I Need A Fence Post Mounted On A Concrete Pad. How a bout core drill the deck, drop/drive in a steel post, and grout it in... Then use some brackets to attach the wood post to the steel post.
How to Attach Posts to a Cement Patio How to Attach Posts to a Cement Patio. What You'll Need. Drill ... attach a concrete bit to the drill. You need a bit that is no wider than the anchor. ... Slide each post into the bracket until it’s pushing against the metal bottom. There will be a hole, possibly two, on each of the side panels.